Appliance organizations, similar to other major companies, have actually their share of takeovers, buyouts and cross-brand agreements.
The same machine design is marketed under several different brand names or model names in some cases.
Other manufacturers merged or purchased other businesses, and create a number of different designs beneath the same name brand. Different designs are differentiated when you’re an alternate “model” or “show.”
Confusing the presssing problem a lot more, some manufacturers “private label” their devices for big malls. Such as for example Sears’ Kenmore and Montgomery Ward’s Signature machines.
Check the after list to see whether you’ve got one of these simple “cross-branded” devices. In that case, you your fix information will be when you look at the chapter for the design.
TO CORRECTLY IDENTIFY THE WASHER, PLEASE MAKE SURE TO BROWSE “THE TOP FIVE,” STARTING IN SECTION 1-1(a) BELOW.
ADMIRAL: Maytag Herrin CROSLEY: Maytag Herrin FRANKLIN: Frigidaire GIBSON: Frigidaire HOTPOINT: General Electrical INGLIS: Whirlpool J.C. PENNEY: General Electrical KELVINATOR: Frigidaire KENMORE: Whirlpool KITCHENAID: Whirlpool MAGIC CHEF: Maytag Herrin MONTGOMERY WARD: Maytag Herrin or Frigidaire PENNCREST: General Electrical RCA: General Electrical ROPER: Whirlpool SIGNATURE: Maytag Herrin or Frigidaire SPEED QUEEN: Amana WHITE-WESTINGHOUSE: Frigidaire
1-1(a) THE TOP FIVE
After will be the main domestic manufacturers associated with devices offered in america and Canada.
WHIRLPOOL: Through the 50’s into the first 80’s, Whirlpool used basically the very same, dependable, bullet-proof design. These are typically understood within the right parts homes as “Whirlpool belt-drive” models.
During the early 80’s, Whirlpool started manufacturing their “Design 2000” washers. They are understood within the components homes as “Whirlpool drive that is direct models.
Both are covered in this guide, in Chapters 3 & 4.
Into the ’90’s, Whirlpool bought KitchenAid. KitchenAid and Roper devices are direct-drive.
Kenmore washers are, and also have been, private-labelled “Whirlpool” washers, both belt-drive and direct-drive.
Into the ’90’s, WCI ended up being purchased by Swedish giant Electrolux, whom changed the business title back into the Frigidaire Residence items business. They seem to have redesigned practically their lineup that is entire in my never-to-be-humble opinion, this new designs are one heckuva great deal much better than the old designs.
They have been nevertheless promoting services and products under Frigidaire and Gibson; in the event that you go through the model quantity, it’s going to begin with a G or an F. nonetheless, the look is similar.
Some Montgomery Ward / Signature machines had been manufactured by WCI, some by Norge (see Maytag.)
AMANA: exact exact Same business as Speed Queen for awhile. Maytag has bought Amana, but around this writing, this has maybe perhaps not shown up as variations in their brand.
MAYTAG: Maytag has two various washers that are top-loading the Maytag brand.
“Performa” and “Atlantis” devices are caused by the purchase associated with Norge and Crosley line (and design) by Maytag. Norge had been the designer that is original of devices. They are referred to as Maytag “Herrin” machines when you look at the components homes. They usually have proceeded to produce these “Herrin” devices as Maytag “Performa” models and high-end Crosley brand name devices, however they have actually experienced lots of development.
A few of the older Montgomery Ward / Signature machines are Norge machines.
1-2 BEFORE YOU BEGIN
If you’re testing, state, a solenoid, first be sure that the solenoid leads are maybe not attached to any such thing, specially an electric supply. In the event that solenoid’s leads are nevertheless attached to one thing, you might obtain a reading throughout that something. If there is nevertheless real time energy from the product you are testing for continuity, you may burn your VOM out instantly and possibly surprise your self.
Touch the 2 test results in the 2 bare cable ends or terminals of this solenoid. You are able to touch escort service Richardson the ends regarding the cables and test leads along with your arms if required to obtain better contact. The voltage that the VOM batteries create is quite low, and you also shall never be surprised. The meter won’t move if there is NO continuity. The meter will move toward the right side of the scale and steady on a reading if there is GOOD continuity. This is basically the opposition reading and it also does not concern us; we just worry that people reveal good continuity. In the event that meter moves just almost no and remains towards the side that is left of scale, that is BAD continuity; the solenoid isn’t any good.
You will show little or no resistance (good continuity) when the switch is closed, and NO continuity when the switch is open if you are testing a switch. If you fail to, the switch is bad.
Figure 1-5: Testing Continuity
Ammeters are a definite small little more complex to spell out without starting plenty of electric concept. You probably already know how to use it if you own an ammeter.
If you do not, aren’t getting one. Ammeters are costly. As well as for our purposes, there are some other techniques to know what an ammeter tests for. If you don’t possess one, skip this part.
For the purposes, ammeters are simply just a real method of testing for continuity without the need to cut to the system or even to disconnect power from whatever its we are testing.
Ammeters gauge the present in amps moving by way of a cable.
The more the existing that is moving via a cable, the greater the thickness of this field that is magnetic creates round the cable. The ammeter just steps the effectiveness of this field that is magnetic and therefore the actual quantity of present, moving through the cable. To find out continuity, for the purposes, we could just separate the component that individuals’re testing ( so we usually do not inadvertently gauge the current going right on through some other elements) and find out if there’s anycurrent flow.
To utilize your ammeter, first make sure it really is for a proper scale (0 to 10 or 20 amps can do). Isolate a cable leading right to the component you are testing. Place the ammeter loop around that cable and browse the meter. (Figure 1-6)